Complete Diagnostic Solutions for Your Repair Needs! 866-217-0063

Ford VCMM Advanced Kit With Full Rugged Tablet OEM Dealer

No reviews yet Write a Review
SKU:
174
$7,495.00

Description

Give us a call 866-217-0063!

The Vehicle Communication & Measurement Module (VCMM) combines all of the functionality of the VMM, VCM II, and MTS 4000/4100 vibration analyzer in an industry leading one-box solution. The combining of this functionality will provide dealers with industry leading diagnostic capability at a significantly lower cost of ownership. FULLY RUGGED DELL 8GB SUPER FAST Tablet INCLUDED, as a bonus SOFTWARE LICENSE INCLUDED WITH THIS KIT


This fully rugged tablet is the preferred tablet from Rotunda that meets or exceeds the specifications to run the IDS software with the VCMM, VCM or VCM II. The Getac tablet has been thoroughly tested with the IDS software. See item 164-R9812 for current specifications.

This Kit Includes:

Ford VCMM Advanced KIT

Getac Tough Tablet (Lifetime Warranty)

Ford Dealer Software License Included

Ford Premium Tech Support

This Kit Comes Set Up and Ready To Go



FORD VCMM

DIAGNOSTIC CAPABILITY (DOES IT ALL)

Retrieve CMDTC's

KOEO (Key-On-Engine-Off)

KOER (Key-On-Engine-Running)

Data logger

Body

Chassis

Electrical

Powertrain

Pressure/Vacuum Tests

Network Test

Module Programming

Programmable Module Installation

Module Reprogramming

Programmable Parameters

Body Tools

PATS Functions
*See Note Below

Remote Keyless Entry

Factory Keyless Entry Code

Restraints

Chassis Tools

Bleed anti-lock brakes

IVD Initialization Sequence

Ride Height Calibration

Pneumatic Test

Accurate Trim Test

Electrical Tools

Charging System Test

Parking Aid Switch Test

Audio

Powertrain Tools

EVAP Test

Fuel Economy Test

Fuel System Test/RelativeInjector Flow Test
(VCM and VMM modules are required on some vehicles)

Ignition System Test

Spark Duration PIDs

Power Balance Test

Relative Compression Test

Transmission Test
(IDS - Some vehicles require only VCM)

Engine Checks and OBD Tests
(Drive Cycle, Mode 01, Mode 06 & Mode 09)

EGR Test

Other Powertrain tests & functions



FEATURES

  • Vehicle Communication (VCM II capability)
  • Customer Flight Recorder capable
  • 4-Channel Oscilloscope
  • 4-Channel Digital Multi-meter
  • 5th-Channel direct monitoring of the DLC connector
  • Vibration Analysis
  • Driveline Balance
  • Signal Generator



4/5 Channel Oscilloscope

  • Improved user interface from VMM
  • Four independent differential Input Channels enables independent monitoring of signal types such as monitoring voltage while concurrently measuring voltage drop across the circuit.
  • A Fifth High Speed Channel that can directly monitor CAN signals at the DLC connector
  • Capture/Record capability to assist in capturing intermittent issues
  • Advanced Triggering capability
  • Pre-Configured setup configuration for common signals and procedures
  • New “Time/Angle” time based settings (CKP/CMP timing diagnostics)



Vibration Analysis and Driveline Balance

  • Similar functionality to the MTS 4000/4100
  • Improved user interface with reduced configuration and setup time
  • Color display
  • Record capacity
  • “Strobe light Pick up loop” for improved component identification*
  • Second vibration transducer
  • Dual Plane driveline balance


The Digital Multi-Meter

  • Monitor up to four independent readings at the same time
  • Capture/Record history
  • Graphing capability for up to two channels
  • Voltage, Current, Resistance, Pulse Width, Duty Cycle, Frequency and Period


Signal Generator

  • User configurable settings for signal waveform types: sine, square, triangle, pulse generator, DC voltage and arbitrary.
  • Verify integrity of module input wiring and the module hardware
  • Improved interface and greater adjustability of voltage and frequency.

System Requirements:
The VCMM will run on any Windows 7 or higher operating system that has 8GB of RAM or higher.
IDS software subscription required.





Extra Information

Brand:
Ford